差異處

這裏顯示兩個版本的差異處。

--- syntec-okura-manual [2020/05/18 13:25]
jay0324 建立
+++ syntec-okura-manual [2022/08/13 15:24] (目前版本)
jay0324 [Electronic Drawing]
@@ 行 1: / 行 1: @@
-this is syntec manual for okura
+====== SYNTEC MT Series Manual ======
+----
+===== Machine Operational Manual =====
+  * [[https://drive.google.com/file/d/1_iDUG_U1l1t5utCHONBXoNbioJetshAP/view?usp=sharing |MT Series Machine Specification]]
+  * [[ https://drive.google.com/file/d/1_ds6_LnfQSyUlbl39l9itP_1t0sM96Gv/view?usp=sharing |MT Series Operational Manual]]
+<WRAP center round important 100%>
+Please Note: Some chapters from the MT Series Operational Manual are only for the FANUC Controller, therefore, please find the related information through SYNTEC official controller Manual.
+</WRAP>
+===== SYNTEC Controller Manual  =====
+  * Main Board: SYNTEC 21TA-H
+  * Software Version: 10.118.22T
+  * PLC Version: 1.05
+  * OP Board: 4018T3
+  * {{ :en:21_series_lathe_operation_manual-en.pdf |Syntec Official Controller Manual}}
+  * {{ :en:lathe_programming_manual.pdf |Syntec Official Programming Manual}}
+===== Operation Pannel =====
+{{ :en:21tah-controller.jpg?nolink |}}
+{{ :en:4018t3.jpg?nolink |}}
+<WRAP center round box 100%>
+  - USB Port
+  - LCD Screen
+  - FMenu bar keys
+  - Switch function Keys
+  - Reset Key
+  - Address-numeric Keypad
+  - Page Keys
+  - Cursor Keys
+  - Editing Keys
+  - MPG
+  - Cycle Start/Stop Buttons
+  - Mode Keys
+  - Feedrate keys
+  - Axis Select keys
+  - G1 Feedrate keys
+  - G0 Feedrate keys
+  - Spindle Speed keys
+  - Spindle Control keys
+  - Not Used
+  - Light On/Off
+  - Lubrication On/Off
+  - Chip On/Off
+  - Chuck Open/Close
+  - Coolant On/Off
+  - Not Used
+  - Optional Stop
+  - Optional Skip
+  - Single Block
+  - MPG Simulation
+  - Livetool A On/Off (JOG/MPG)
+  - Livetool B On/Off (JOG/MPG)
+  - F1: Auto Door Open/Close
+  - F2: Dry Run
+  - F3: Machine Lock
+  - F4: Air Blow
+  - Overtravel Button
+  - F5: Not Used
+  - Program Lock key
+  - Power On/Off Buttons
+  - Emergency Stop Button
+</WRAP>
+<WRAP center round important 100%>
+//**COMBO Key**//
+  - C Axis On/Off: JOG Mode -> [C+][C-]
+</WRAP>
+===== Custom G Code =====
+  * G101: Hex Milling
+===== Custom M Code =====
+  * M00: Feed Hold
+  * M01: Optional Stop
+  * M02: Program Stop
+  * M03: 1th Spindle CW
+  * M04: 1th Spindle CCW
+  * M05: 1th Spindle STOP
+  * M06: Set Main Spindle to 1th Spindle
+  * M08: Coolant Pump On
+  * M09: Coolant Pump Off
+  * M10: Chuck Open
+  * M11: Chuck Close
+  * M19: Spindle Orientation (Pr1751 set degree)
+  * M22: CS Off
+  * M23: CS On
+  * M30: Cycle End
+  * M31: Barloader Start
+  * M33: Live Tool B CW
+  * M34: Live Tool B CCW
+  * M35: Live Tool B STOP
+  * M43: Live Tool A CW
+  * M44: Live Tool A CCW
+  * M45: Live Tool A STOP
+  * M46: Set Main Spindle to Live Tool A
+  * M48: Robot On
+  * M49: Robot Off
+  * M64: Door Open
+  * M65: Door Close
+  * M70: Spindle Jog for Air Blow
+  * M88: Air Blow Open
+  * M89: Air Blow Close
+  * M94: Barloader Back Start
+  * M95: Barloader End
+  * M98: Sub program Begin
+  * M99: Sub program End
+===== Electronic Drawing =====
+[[ https://drive.google.com/file/d/1_eqWYQ_oQ4HW2h6ZEnL6bAF8xc5BwVBb/view?usp=sharing |Electronic Drawing For 380V 6KVA]]
+<wrap em>(UPDATE: 20200527)</wrap>